smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.54-Unraid] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD322HJ Serial Number: S17AJDWSA04579 LU WWN Device Id: 5 0024e9 0024149c8 Firmware Version: 1AC01118 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.5/5988 ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat Dec 13 12:11:32 2025 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3994) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 67) minutes. Conveyance self-test routine recommended polling time: ( 8) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 092 051 - 0 3 Spin_Up_Time POS--- 086 086 011 - 5180 4 Start_Stop_Count -O--CK 096 096 000 - 3928 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 3 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Hours -O--CK 092 092 000 - 41020 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 4 12 Power_Cycle_Count -O--CK 098 098 000 - 1619 13 Read_Soft_Error_Rate -OSR-- 100 092 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 314 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 083 052 000 - 17 (Min/Max 17/17) 194 Temperature_Celsius -O---K 083 052 000 - 17 (Min/Max 17/17) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 1262 196 Reallocated_Event_Count -O--CK 100 100 000 - 3 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 099 000 - 6 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 2 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 158 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 158 [5] occurred at disk power-on lifetime: 22343 hours (930 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 53 00 00 00 00 00 6a 50 a6 e0 00 Error: ICRC, ABRT at LBA = 0x006a50a6 = 6967462 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 08 00 00 00 6a 50 9f e0 00 00:06:27.430 READ DMA EXT 25 00 03 00 08 00 00 00 2a 00 d7 e0 00 00:06:27.410 READ DMA EXT 25 00 03 00 08 00 00 00 68 ac a7 e0 00 00:06:27.400 READ DMA EXT 25 00 03 00 08 00 00 05 5e e9 ef e0 00 00:06:27.380 READ DMA EXT 25 00 03 00 08 00 00 00 63 fc 0f e0 00 00:06:27.370 READ DMA EXT Error 157 [4] occurred at disk power-on lifetime: 22343 hours (930 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 12 a1 7f 87 e0 00 128 sectors at LBA = 0x12a17f87 = 312573831 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 80 00 00 12 a1 7f 07 e0 00 00:02:35.770 READ DMA EXT 25 00 03 00 80 00 00 12 a1 7e 87 e0 00 00:02:35.770 READ DMA EXT 25 00 03 00 80 00 00 12 a1 7e 07 e0 00 00:02:35.770 READ DMA EXT 25 00 03 00 80 00 00 12 a1 7d 87 e0 00 00:02:35.770 READ DMA EXT 25 00 03 00 80 00 00 12 a1 7d 07 e0 00 00:02:35.770 READ DMA EXT Error 156 [3] occurred at disk power-on lifetime: 22343 hours (930 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 12 a1 5b 07 e0 00 128 sectors at LBA = 0x12a15b07 = 312564487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 80 00 00 12 a1 5a 87 e0 00 00:02:35.480 READ DMA EXT 25 00 03 00 80 00 00 12 a1 5a 07 e0 00 00:02:35.480 READ DMA EXT 25 00 03 00 80 00 00 12 a1 59 87 e0 00 00:02:35.480 READ DMA EXT 25 00 03 00 80 00 00 12 a1 59 07 e0 00 00:02:35.480 READ DMA EXT 25 00 03 00 80 00 00 12 a1 58 87 e0 00 00:02:35.470 READ DMA EXT Error 155 [2] occurred at disk power-on lifetime: 22343 hours (930 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 12 a1 53 07 e0 00 128 sectors at LBA = 0x12a15307 = 312562439 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 80 00 00 12 a1 52 87 e0 00 00:02:35.300 READ DMA EXT 25 00 03 00 80 00 00 12 a1 52 07 e0 00 00:02:35.300 READ DMA EXT 25 00 03 00 80 00 00 12 a1 51 87 e0 00 00:02:35.290 READ DMA EXT 25 00 03 00 80 00 00 12 a1 51 07 e0 00 00:02:35.290 READ DMA EXT 25 00 03 00 80 00 00 12 a1 50 87 e0 00 00:02:35.290 READ DMA EXT Error 154 [1] occurred at disk power-on lifetime: 22342 hours (930 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- d0 00 80 00 00 01 ba f3 77 e0 00 128 sectors at LBA = 0x01baf377 = 29029239 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 80 00 00 01 ba f2 f7 e0 00 01:07:07.310 READ DMA EXT 25 00 03 00 80 00 00 01 ba f2 77 e0 00 01:07:07.310 READ DMA EXT 25 00 03 00 80 00 00 01 ba f1 f7 e0 00 01:07:07.310 READ DMA EXT 25 00 03 00 80 00 00 01 ba f1 77 e0 00 01:07:07.310 READ DMA EXT 25 00 03 00 80 00 00 01 ba f0 f7 e0 00 01:07:07.310 READ DMA EXT Error 153 [0] occurred at disk power-on lifetime: 14564 hours (606 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0c d2 a5 ff e0 00 Error: UNC at LBA = 0x0cd2a5ff = 215131647 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 0c d2 a5 bf e0 08 9d+03:19:17.520 READ DMA EXT 35 00 00 00 78 00 00 22 23 49 ff e0 08 9d+03:19:17.520 WRITE DMA EXT 25 00 00 00 80 00 00 0c d2 a5 3f e0 08 9d+03:19:17.520 READ DMA EXT 35 00 00 00 7a 00 00 22 23 49 7d e0 08 9d+03:19:17.520 WRITE DMA EXT 25 00 00 00 80 00 00 0c d2 a4 bf e0 08 9d+03:19:17.520 READ DMA EXT Error 152 [7] occurred at disk power-on lifetime: 7700 hours (320 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 15 c8 f0 47 e0 00 Error: UNC at LBA = 0x15c8f047 = 365490247 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 15 c8 f0 47 e0 08 11d+01:19:53.950 READ DMA EXT 35 00 00 00 01 00 00 10 91 44 3f e0 08 11d+01:19:53.950 WRITE DMA EXT 25 00 00 00 08 00 00 05 10 15 bf e0 08 11d+01:19:53.950 READ DMA EXT 25 00 00 00 08 00 00 05 10 11 a7 e0 08 11d+01:19:53.940 READ DMA EXT 35 00 00 00 79 00 00 05 0f e5 af e0 08 11d+01:19:53.940 WRITE DMA EXT Error 151 [6] occurred at disk power-on lifetime: 7700 hours (320 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 15 c8 f0 47 e0 00 Error: UNC at LBA = 0x15c8f047 = 365490247 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 15 c8 f0 47 e0 08 11d+01:19:51.870 READ DMA EXT 25 00 00 00 10 00 00 15 c8 f0 37 e0 08 11d+01:19:51.860 READ DMA EXT 25 00 00 00 08 00 00 14 a1 74 7f e0 08 11d+01:19:51.840 READ DMA EXT 25 00 00 00 08 00 00 05 10 15 b7 e0 08 11d+01:19:51.840 READ DMA EXT 25 00 00 00 08 00 00 05 10 13 3f e0 08 11d+01:19:51.840 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: --/17 Celsius Lifetime Min/Max Temperature: --/51 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (92) Index Estimated Time Temperature Celsius 93 2025-12-13 10:04 22 *** ... ..( 5 skipped). .. *** 99 2025-12-13 10:10 22 *** 100 2025-12-13 10:11 23 **** 101 2025-12-13 10:12 22 *** ... ..( 24 skipped). .. *** 126 2025-12-13 10:37 22 *** 127 2025-12-13 10:38 23 **** 0 2025-12-13 10:39 23 **** 1 2025-12-13 10:40 23 **** 2 2025-12-13 10:41 22 *** 3 2025-12-13 10:42 23 **** ... ..( 26 skipped). .. **** 30 2025-12-13 11:09 23 **** 31 2025-12-13 11:10 24 ***** 32 2025-12-13 11:11 24 ***** 33 2025-12-13 11:12 23 **** 34 2025-12-13 11:13 24 ***** 35 2025-12-13 11:14 23 **** 36 2025-12-13 11:15 24 ***** 37 2025-12-13 11:16 23 **** 38 2025-12-13 11:17 24 ***** 39 2025-12-13 11:18 24 ***** 40 2025-12-13 11:19 23 **** 41 2025-12-13 11:20 24 ***** ... ..( 6 skipped). .. ***** 48 2025-12-13 11:27 24 ***** 49 2025-12-13 11:28 23 **** 50 2025-12-13 11:29 24 ***** ... ..( 34 skipped). .. ***** 85 2025-12-13 12:04 24 ***** 86 2025-12-13 12:05 23 **** 87 2025-12-13 12:06 24 ***** ... ..( 2 skipped). .. ***** 90 2025-12-13 12:09 24 ***** 91 2025-12-13 12:10 17 - 92 2025-12-13 12:11 17 - SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error aborted command Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC