smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.54-Unraid] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue (CMR) Device Model: WDC WD40EZRZ-00GXCB0 Serial Number: WD-WCC7K2DANEHU LU WWN Device Id: 5 0014ee 2b8865db6 Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.5/5988 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Dec 13 11:52:37 2025 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (44820) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 475) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 071 051 - 14 3 Spin_Up_Time POS--K 163 162 021 - 6841 4 Start_Stop_Count -O--CK 093 093 000 - 7741 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 3 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 081 081 000 - 14114 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5061 192 Power-Off_Retract_Count -O--CK 200 200 000 - 303 193 Load_Cycle_Count -O--CK 084 084 000 - 350583 194 Temperature_Celsius -O---K 128 098 000 - 22 196 Reallocated_Event_Count -O--CK 199 199 000 - 1 197 Current_Pending_Sector -O--CK 200 200 000 - 10 198 Offline_Uncorrectable ----CK 200 200 000 - 9 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 13 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 6 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 56 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 13381 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13381 [12] occurred at disk power-on lifetime: 14108 hours (587 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3e 21 90 40 00 Error: UNC at LBA = 0x003e2190 = 4071824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 78 00 00 00 3e 21 90 40 08 18:02:10.131 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 30 e0 08 18:02:10.103 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 e0 08 18:02:10.103 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 18:02:10.103 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 18:02:10.103 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 13380 [11] occurred at disk power-on lifetime: 14108 hours (587 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3e 21 90 40 00 Error: UNC at LBA = 0x003e2190 = 4071824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 00 3e 21 90 40 08 18:02:06.090 READ FPDMA QUEUED 60 00 08 00 58 00 00 00 3e 21 88 40 08 18:02:06.089 READ FPDMA QUEUED 60 00 08 00 50 00 00 00 3e 21 80 40 08 18:02:06.089 READ FPDMA QUEUED 60 00 08 00 48 00 00 00 3e 21 78 40 08 18:02:06.089 READ FPDMA QUEUED 60 00 08 00 40 00 00 00 3e 21 70 40 08 18:02:06.089 READ FPDMA QUEUED Error 13379 [10] occurred at disk power-on lifetime: 14108 hours (587 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3e 11 a0 40 00 Error: UNC at LBA = 0x003e11a0 = 4067744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 00 3e 10 50 40 08 18:01:57.601 READ FPDMA QUEUED 60 00 08 00 a8 00 00 00 3e 10 48 40 08 18:01:57.601 READ FPDMA QUEUED 60 00 08 00 a0 00 00 00 3e 10 40 40 08 18:01:57.601 READ FPDMA QUEUED 60 00 08 00 98 00 00 00 3e 10 38 40 08 18:01:57.601 READ FPDMA QUEUED 60 00 08 00 90 00 00 00 3e 10 30 40 08 18:01:57.601 READ FPDMA QUEUED Error 13378 [9] occurred at disk power-on lifetime: 14108 hours (587 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3e 21 90 40 00 Error: UNC at LBA = 0x003e2190 = 4071824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 c0 00 c8 00 00 00 3e 13 40 40 08 18:01:48.045 READ FPDMA QUEUED 60 04 b0 00 c0 00 00 00 3e 1d 50 40 08 18:01:48.044 READ FPDMA QUEUED 60 05 50 00 b0 00 00 00 3e 18 00 40 08 18:01:48.044 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 30 e0 08 18:01:48.043 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 e0 08 18:01:48.043 READ LOG DMA EXT Error 13377 [8] occurred at disk power-on lifetime: 14108 hours (587 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3e 11 a0 40 00 Error: UNC at LBA = 0x003e11a0 = 4067744 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 04 c0 00 f8 00 00 00 3e 13 40 40 08 18:01:42.188 READ FPDMA QUEUED 60 05 40 00 b8 00 00 00 3e 0e 00 40 08 18:01:42.188 READ FPDMA QUEUED 60 04 c0 00 b0 00 00 00 3e 09 40 40 08 18:01:41.256 READ FPDMA QUEUED 60 05 40 00 a8 00 00 00 3e 04 00 40 08 18:01:41.256 READ FPDMA QUEUED 60 04 c0 00 a0 00 00 00 3d ff 40 40 08 18:01:41.252 READ FPDMA QUEUED Error 13376 [7] occurred at disk power-on lifetime: 14091 hours (587 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 cd e2 78 40 00 Error: UNC at LBA = 0x08cde278 = 147710584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 08 cd e2 78 40 08 00:10:38.992 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 30 e0 08 00:10:38.991 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 e0 08 00:10:38.991 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:10:38.991 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:10:38.991 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 13375 [6] occurred at disk power-on lifetime: 14091 hours (587 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 cd e2 78 40 00 Error: UNC at LBA = 0x08cde278 = 147710584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 08 cd e2 78 40 08 00:10:34.986 READ FPDMA QUEUED 47 00 00 00 01 00 00 00 00 00 30 e0 08 00:10:34.985 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 e0 08 00:10:34.985 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:10:34.985 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:10:34.985 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 13374 [5] occurred at disk power-on lifetime: 14091 hours (587 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 cd e2 78 40 00 Error: UNC at LBA = 0x08cde278 = 147710584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a8 00 00 08 cd 90 d8 40 08 00:10:30.836 READ FPDMA QUEUED 60 00 08 00 a0 00 00 08 cd 90 d0 40 08 00:10:30.835 READ FPDMA QUEUED 60 00 08 00 98 00 00 08 cd 90 c8 40 08 00:10:30.835 READ FPDMA QUEUED 60 00 08 00 90 00 00 08 cd 90 c0 40 08 00:10:30.835 READ FPDMA QUEUED 60 00 08 00 88 00 00 08 cd 90 b8 40 08 00:10:30.835 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14113 - # 2 Extended offline Completed: read failure 90% 14093 40561832 # 3 Short offline Completed without error 00% 12346 - # 4 Short offline Completed without error 00% 11641 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 21/22 Celsius Lifetime Min/Max Temperature: 12/52 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (33) Index Estimated Time Temperature Celsius 34 2025-12-13 03:55 23 **** ... ..(140 skipped). .. **** 175 2025-12-13 06:16 23 **** 176 2025-12-13 06:17 ? - 177 2025-12-13 06:18 23 **** 178 2025-12-13 06:19 23 **** 179 2025-12-13 06:20 23 **** 180 2025-12-13 06:21 24 ***** 181 2025-12-13 06:22 24 ***** 182 2025-12-13 06:23 24 ***** 183 2025-12-13 06:24 ? - 184 2025-12-13 06:25 22 *** 185 2025-12-13 06:26 22 *** 186 2025-12-13 06:27 22 *** 187 2025-12-13 06:28 23 **** 188 2025-12-13 06:29 23 **** 189 2025-12-13 06:30 24 ***** 190 2025-12-13 06:31 24 ***** 191 2025-12-13 06:32 24 ***** 192 2025-12-13 06:33 25 ****** 193 2025-12-13 06:34 25 ****** 194 2025-12-13 06:35 25 ****** 195 2025-12-13 06:36 26 ******* 196 2025-12-13 06:37 26 ******* 197 2025-12-13 06:38 26 ******* 198 2025-12-13 06:39 27 ******** 199 2025-12-13 06:40 27 ******** 200 2025-12-13 06:41 ? - 201 2025-12-13 06:42 20 * 202 2025-12-13 06:43 ? - 203 2025-12-13 06:44 21 ** 204 2025-12-13 06:45 21 ** 205 2025-12-13 06:46 22 *** 206 2025-12-13 06:47 31 ************ ... ..(115 skipped). .. ************ 322 2025-12-13 08:43 31 ************ 323 2025-12-13 08:44 30 *********** ... ..( 46 skipped). .. *********** 370 2025-12-13 09:31 30 *********** 371 2025-12-13 09:32 29 ********** 372 2025-12-13 09:33 29 ********** 373 2025-12-13 09:34 28 ********* 374 2025-12-13 09:35 28 ********* 375 2025-12-13 09:36 28 ********* 376 2025-12-13 09:37 27 ******** ... ..( 3 skipped). .. ******** 380 2025-12-13 09:41 27 ******** 381 2025-12-13 09:42 26 ******* ... ..( 2 skipped). .. ******* 384 2025-12-13 09:45 26 ******* 385 2025-12-13 09:46 25 ****** ... ..( 6 skipped). .. ****** 392 2025-12-13 09:53 25 ****** 393 2025-12-13 09:54 24 ***** ... ..( 13 skipped). .. ***** 407 2025-12-13 10:08 24 ***** 408 2025-12-13 10:09 23 **** ... ..(102 skipped). .. **** 33 2025-12-13 11:52 23 **** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 5061 --- Lifetime Power-On Resets 0x01 0x010 4 14114 --- Power-on Hours 0x01 0x018 6 89609879855 --- Logical Sectors Written 0x01 0x020 6 297618819 --- Number of Write Commands 0x01 0x028 6 160707265230 --- Logical Sectors Read 0x01 0x030 6 1076382538 --- Number of Read Commands 0x01 0x038 6 3565759744 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 12415 --- Spindle Motor Power-on Hours 0x03 0x010 4 6834 --- Head Flying Hours 0x03 0x018 4 350887 --- Head Load Events 0x03 0x020 4 24 --- Number of Reallocated Logical Sectors 0x03 0x028 4 192650 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 80 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 303 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 13241 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 8782391 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 30 --- Average Short Term Temperature 0x05 0x018 1 37 --- Average Long Term Temperature 0x05 0x020 1 52 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 47 --- Highest Average Short Term Temperature 0x05 0x038 1 23 --- Lowest Average Short Term Temperature 0x05 0x040 1 43 --- Highest Average Long Term Temperature 0x05 0x048 1 30 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 73390 --- Number of Hardware Resets 0x06 0x010 4 66529 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 180 Vendor specific